I have multiple linux computers, from servers to a surface tablet, i am able to use all different generations of all nvidia, both permanently installed, and eGPU. It is not without any issue, but it works and is usable.
For me issues stem from x11 vs wayland (work computer is ubuntu due to company policy), or egpu shenanigans which I feel is platform agnostic
It may have been a rate of rise vs a hard upper limit for the heat detector. If it was, about 8-10°C / 15-20°F change per minute would set it off. Makes sense for it to go off over an oven. The hard upper limit type are single use, I don’t know if that causes them to repeatedly go off or not.
Either way with more regulated short term rentals, a fire inspection would likely have flagged that.
There is nuance in installing fire alarms, make sure you are using the correct detector type for each area, and installing it correctly.
I’m pretty sure strong drafts or dusty areas can set it off.
Also know that smoke detectors and carbon monoxide detectors are consumable items that should be replaced, usually 7-10 years but it should be noted on the device.
At the end of the day, it wakes you up to check, or causes you to observe for an emergency. Imagine your wake up groggy situation but you smell smoke. Personally I would like that chance to be able to evacuate.
Verizon and ATT just rebrand nokia ONTs and roll some of their own software that is mostly enhanced or changed encryption at L1. Can’t speak for Comcast, I only know about the other two as I’m in a smaller ISP that competes with them.
They use have L2 onts that don’t have any gateway functions, just fiber to ethernet with some extra overhead to monitor the connection between the hose and shelf.
The ONT-on-a-stick units do the same thing, just a more compact and expensive interface that doesn’t have great support, unless comcast or running all home run fibers where they can just provide a straight SFP instead of doing any optical splitting.
No, you are likely looking at an ONT (optical network terminal), and it is not a router. Even with a port that accepts the fiber (sfp or sfp+ for 10g) on your equipment, the OLT (optical line terminal) likely will not provide you with service.
If you were to match the wavelengths the ISP is using you are likely to become a “rogue” on their PON that can knock out service for other customers that share the same passive network as you.
I make assumptions about you being on PON since you say AT&T, generally all I have ever seen from them are passive networks (one fiber with splitters for 1 port to many customers) unless you are paying extra for “dedicated” ($$$$$) internet.
If they are using a ONT with an “RG” (residential gateway) which is the typical “all in one” you can request the gateway service can be removed and replaced with a layer 2 bridge, where you’re router/firewall gets the “external” addressing and there is nothing being done by the ISP equipment other than sending you traffic and OAM (operations, administration, and maintenance; usually check or alert for light levels, software status, if a part of the ONT fails etc).
I work for an telco and I have seen a lot of times that a contract for using preexisting underground infrastructure that have lids like this has a section requiring that they are returned to the same location and orientation when the enclosure is sealed.
Whoever owns that, municipality or private, will probably take a complaint about it, and may pass it to whoever is responsible or owns the plant inside.
I am working to decommission a windows server, which is currently using 500gb ram, and i have moved all functions to a different application, same purpose and very similar underlying methodology… 32gb of ram on linux. it’s crazy how much bloat windows admins are willing to accept.
apparently it was actually someone shooting fireworks at a cop, after the fourth sales prolly
I have a different vibration pattern for my wife’s calls and messages, work calls and messages, and all others. I swear I will get phantom vibrations from a specific set randomly.
For indoor cameras, I use TP-Link tapo wireless cameras, and hikvision for outdoor. I put all of them on an isolated camera wlan and vlan without internet. the tapos work fine without internet access, but the status light will always be orange as it tries to reach some tplink aws IP to verify connectivity.
All the hikvision cameras and tapos support rtsp.
typically you only need one power supply to run it, once you move to redundant power you can use the second one in case the first one fails. when you plug both in it will just balance across both until one fails.
in my opinion, hardware should only be hypervisors that run virtual machines, then you can provision VMs, similar to using VPSs. going this route you will need a vga monitor for initial setup, eventually everything is done over the lan with a web ui or ssh.
i use proxmox which is Debian based for the hypervisor.
As far as what you do with it, is that you can in theory replace the VPSs or test software in your lan.
to compare, i have my router (vyos), homeassistant, a docker server for hosting small services, a network lab (gns3), windows and mac VMs, and more running on a cluster that is using similar hardware.
screenshot of a screenshot looks like
it looks like there is a bedrock branch, but i personally have no experience with bedrock.
see this issue for more details: https://github.com/minekube/gate/issues/11
i have used gate for my internal and external, works very well and i do exactly what you are asking and separate different versions and modpacks by name https://github.com/minekube/gate
i think with fingerprinting, it provides evidence that someone touched something, not that someone did not touch it
everything should be behind a firewall
i didn’t downvote but 17v on a 12v battery maybe seems a bit high. I’m more used to about 7-14% over (maybe up to 14v on a 12v batt) when charged/floating but i don’t use solar anywhere currently, and i usually work on 48v systems. i normally expect to see about 54v on a fully charged battery string (13.5v per battery x4) with the rectifiers running.
i also second the opinion of running an automotive PSU for this situation.
edit: i looked it up since i was curious, some “12v” solar panels can output between 16-20v, but it’s recommended that you would use a charge controller, especially if you have lead-acid batteries
i think the issue is not necessarily that voters who are disappointed by biden on this issue would vote for trump directly, or even think he would make a different or “better” choice but instead may not turn out, or vote for a 3rd party candidate. with the race as close as it is now, that might be all it takes.
let’s take an entry level hobby electronics activity and do our best not to learn anything by using chatgpt??? what’s the point??